Model |
MEG Z890 ACE |
Chipset |
INTEL Z890 |
CPU |
Supports Intel Core Ultra Processors (Series 2) LGA 1851 |
Memory |
- 4x DDR5 UDIMM, Maximum Memory Capacity 256GB
Memory Support 9200 - 6400 (OC) MT/s / 6400 - 4800 (JEDEC) MT/s Max. overclocking frequency:
- 1DPC 1R Max speed up to 9200+ MT/s
- 1DPC 2R Max speed up to 7200+ MT/s
- 2DPC 1R Max speed up to 4800+ MT/s
- 2DPC 2R Max speed up to 4800+ MT/s
- Supports Intel POR Speed and JEDEC Speed
- Supports Memory Overclocking and Intel XMP 3.0
- Supports Dual-Controller Dual-Channel mode
- Supports Non-ECC, Un-buffered memory
- Supports CUDIMM
* The DIMM slots on this motherboard only have single-sided latches. ** Memory compatibility and supported speeds can vary depending on the CPU and memory configuration. For detailed information
|
Onboard Graphics |
- 1x HDMI
- Support HDMITM 2.1 with FRL port, maximum resolution of 8K 60Hz*
- 2x Type-C DisplayPort
- Thunderbolt 4 ports, supporting DisplayPort 2.1 with UHBR20 over USB Type-C, with a maximum resolution of 4K@120Hz / 8K@60Hz*
* Available only on processors featuring integrated graphics. Graphics specifications may vary depending on the CPU installed.
|
Slot |
- 3x PCI-E x16 slot
- PCI_E1 Gen PCIe 5.0 supports up to x16 (From CPU)
- PCI_E2 Gen PCIe 5.0 supports up to x8 (From CPU)
- PCI_E3 Gen PCIe 4.0 supports up to x4 (From Chipset)
• PCI_E1 support manual BIOS adjustment to X8+X8/X8+X4+X4 • PCI_E2 support manual BIOS adjustment to X4+X4
* PCI_E1 slot will run at x8 speed when PCI_E2 slot installing device. ** PCI_E1 slot will run at x8 speed and PCI_E2 slot will run at x4 speed when installing PCIe Gen 5 M.2 device in the M2_4 slot.
|
Audio |
- Realtek ALC4082 Codec + ESS9219Q Combo DAC/HPA
- 7.1-Channel USB High-Performance Audio
- Supports S/PDIF output
- Supports up to 32-Bit/384 kHz playback on front panel
|
Storage |
- 5x M.2
- M.2_1 Source (From CPU) supports up to PCIe 5.0 x4 , supports 2280/2260 devices
- M.2_2 Source (From CPU) supports up to PCIe 4.0 x4 , supports 2280/2260 devices
- M.2_3 Source (From Chipset) supports up to PCIe 4.0 x4 , supports 2280/2260 devices
- M.2_4 Source (From CPU+Chipset) supports up to PCIe 5.0 x4 + PCIe 4.0 x4 , supports 22110/2280 devices
- M.2_5 Source (From Chipset) supports up to PCIe 4.0 x4 / SATA mode, supports 2280/2260 devices
4x SATA 6G
* M2_4 default from chipset, can support PCIe 5.0 x4 (From CPU) by manual BIOS adjustment. ** Please refer to the manual for M.2 SSD heatsink restrictions.
|
RAID |
- Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA storage devices
- Supports RAID 0, RAID 1, RAID 5 and RAID 10 for M.2 NVMe storage devices
|
Onboard Thunderbolt |
- 2x Thunderbolt4 ports (Rear)
- Support up to 40Gbps transfer rate with Thunderbolt devices
- Support up to 20Gbps transfer rate with USB4 devices
- Support up to 10Gbps transfer rate with USB 3.2 devices
- Support up to 5V/3A,15W power charging
- Each port can daisy-chain up to three Thunderbolt 4 devices or five Thunderbolt 3 devices
- Support up to 8K display
|
USB |
- 4x USB 2.0 (Front)
- 4x USB 5Gbps Type A (Front)
- 11x USB 10Gbps Type A (Rear)
- 2x USB 10Gbps Type C (Rear)
- 1x USB 20Gbps Type C (Front)
* To achieve USB PD 60W fast charging for JUSBC1, the PD_PWR1 connector needs to be connected to the power supply unit. |
LAN |
1x Marvell AQC113CS 10Gbps LAN |
Internal IO |
- 1x Thunderbolt5 card connector(JTBT5, support RTD3)
- 1x Power Connector(ATX_PWR)
- 2x Power Connector(CPU_PWR)
- 1x Power Connector(PCIE_PWR 8pin)
- 1x Front Type-C Quick Charge Connector(PD_PWR1)
- 1x CPU Fan
- 2x Combo Fan (Pump_Sys Fan)
- 5x System Fan
- 1x EZ Conn-header (JAF_2)
- 2x Front Panel (JFP)
- 1x Chassis Intrusion (JCI)
- 1x Water Flow connector
- 1x Slow Mode Booting Jumper(JSLOW)
- 1x Front Audio (JAUD)
- 2x Thermal Sensor connectors(T_SEN)
- 1x Tuning Controller connector(JDASH)
- 3x Addressable V2 RGB LED connector (JARGB_V2)
- 1x RGB LED connector(JRGB)
- 1x TPM pin header(Support TPM 2.0)
- V-check point
- 4x USB 2.0 ports
- 4x USB 5Gbps Type A ports
- 1x USB 20Gbps Type C ports
|
WIRELESS LAN & BLUETOOTH |
- Intel Killer BE1750x Wi-Fi 7
- The Wireless module is pre-installed in the M.2 (Key-E) slot
- Supports MU-MIMO TX/RX, 2.4GHz / 5GHz / 6GHz* (320MHz) up to 5.8Gbps
- Supports 802.11 a/ b/ g/ n/ ac/ ax/ be
- Supports Bluetooth® 5.4**, MLO, 4KQAM
* 6GHz band support may depend on every country’s regulations and Wi-Fi 7 will be ready in Windows 11 version 24H2. ** The Bluetooth version may be updated, please refer to the Wi-Fi chipset vendor’s website for details. Bluetooth 5.4 will be ready in Windows 11 version 24H2.
|
LED FEATURE |
- 4x EZ Debug LED
- 1x EZ Digit Debug LED
- 1x EZ LED Control switch
|
BACK PANEL PORTS |
- USB 10Gbps (Type-A)
- Flash BIOS Button
- Clear CMOS Button
- Smart Button
- 10G LAN
- Wi-Fi / Bluetooth
- HD Audio Connectors
- HDMI 2.1 Port
- Thunderbolt 4 40Gbps (Type-C)
- USB 10Gbps (Type-C)
- USB 10Gbps (Type-A)
- Optical S/PDIF-Out
|
OPERATING SYSTEM |
Support for Windows 11 64-bit |
BOX CONTENT |
- Quicl installation Guide
- Europeon Union Regulatory Notice
- Shout-Out Flyer
- 4x Sata Cables
- EZ M.2 Clips ll
- EZ M.2 Clips ll Remover
- USB Driver
- Cable Sticker
- EZ Wi-Fi Antenna
- 1to3 EZ Conn-Cable (V2)
- EZ Front Panel Cable
- M.2 Screw and Standoff Set
- 1 to 2 RGB Extension cable
- ARGB Extension Cable
- 2xThermistor Cables
|
PCB Info |
|
Warranty |
3 Years |
Note |
*** Images are for Representation purposes only
*** Features, Price, Specifications are subject to change without notice.
|